What is Hot Isostatic Pressing (HIP)?

Near-net-shape HIP manifold with consolidated flow paths in super duplex stainless steel

Hot isostatic pressing (HIP) is a powder metallurgy process that transforms gas-atomized metal powder into fully dense, near-net-shape components. The powder is sealed in a mild steel capsule and consolidated under high argon gas pressure at elevated temperature, producing a fine, defect-free microstructure with practically no inclusions.Sverdrup Steel supplies near-net-shape HIP components via our partner MTC Powder Solutions in Sweden. Typical components include manifolds, valve blocks and chokes for the oil and gas, chemical, marine, nuclear, defence and aerospace industries. Because the powder consolidates into almost any geometry, HIP offers greater design freedom than forging or casting, and near-net-shape blanks reduce material waste, welding, machining and inspection cost. PM HIP is also a proven replacement for conventional forgings in duplex, super duplex and Alloy 625 components, where design freedom and lead time decide project schedules.

What are the advantages of HIP over casting, forging and fabrication?

  • Superior microstructure: HIP components are 100% dense with practically no inclusions, and the very fine microstructure reduces the risk of hydrogen-induced stress cracking (HISC) in duplex stainless steels.

  • Total cost reduction: Near-net-shape blanks mean less material bought, less machining, less welding and fewer inspections and repairs.

  • Tailor-made solutions: Complex geometries that would be very difficult or impossible to manufacture by casting, forging or fabrication.

How it works

Fine metal powder is sealed in a gas‑tight steel capsule, heated (below melting point), and compressed with isostatic gas pressure to create a fully dense, high‑strength part with minimal inclusions.

This HIP process produces near‑net shapes of almost any geometry, offering greater design freedom than forging or casting while reducing risks such as HISC and defects like cracks or porosity. It also cuts lead time and cost by minimizing welding, repairs, and inspections.

The production process consists of four main stages.

 

Gas atomization of molten alloy into spherical metal powder
Step 1

Melting and atomization

Welding a mild steel capsule before hot isostatic pressing
Step 2

Canning

Hot isostatic press consolidating powder capsules under argon pressure
Step 3

Hot isostatic pressing (HIP)

Machined near-net-shape HIP component during post treatment inspection
Step 4

Post treatment

Which materials can be HIPped?

Materials available for hot isostatic pressing (HIP) near-net-shape components via Sverdrup Steel and MTC Powder Solutions
Material group Common grades Why HIP suits it
Duplex & Super Duplex UNS S32205, S32750, S32760 Fine microstructure lowers HISC risk in chloride service; near-net shape cuts cost in high-value grades
Austenitic 316L / 316LN (UNS S31603) Complex manifolds, bends and fittings produced fully dense in one body
Nickel alloys Alloy 625 and other nickel grades Corrosion-critical chokes, hubs and swivels with less material machined away
Martensitic 17-4 PH and martensitic grades Uniform microstructure for strength and wear critical parts
Tool steels PM HIP tool steels Fine, uniform carbide distribution for tooling and wear applications
Metal matrix composites (MMC) Particle reinforced MMC Tailored wear, thermal and stiffness properties for demanding service

Grade availability is project dependent. Contact us to discuss your specification.

 

HIP capability at a glance

Hot isostatic pressing capability and process parameters via MTC Powder Solutions
Parameter Capability
Maximum component diameter 1800 mm
Maximum component height 3550 mm
Maximum component weight Approx. 25 tonnes
Density 100% theoretical, fully dense
Defects No cracks, porosity or stringers; practically no inclusions
Pressure medium Argon gas, typically around 100 MPa
Powder particle size Below 500 micron
Can removal Machining or pickling

Capabilities via our partner MTC Powder Solutions, Sweden.

Cross section of a fully dense HIP component

What is HIP used for?

Near-net-shape HIP pays off wherever complex geometry, material cost or component integrity decides the design.

Together with our partner MTC Powder Solutions we deliver manifolds, hubs and connectors, valve blocks, chokes, bends, tees and fittings, pump and motor casings, blow-out preventer parts, venturis, wye pieces, goosenecks, blind tees and swivels.

The table below shows the components we most often produce and why near-net-shape pressing fits them.

Typical near-net-shape components produced by hot isostatic pressing (HIP)
Typical HIP component Why near-net-shape fits
Manifolds Multiple flow paths consolidated in one body, replacing fabricated weldments and their welding, inspection and leak paths.
Hubs and connectors Complex interface geometries in super duplex and nickel alloys, produced in one piece instead of fabricated.
Valve blocks Integrated bores and cavities pressed near net shape mean less machining of costly grades and lighter components.
Chokes Corrosion-critical bodies in Alloy 625 (UNS N06625), where material savings matter most.
Bends, tees and fittings Smooth internal surfaces and almost any geometry improve flow characteristics in fluid handling systems.
Pump and motor casings Complex external contours and internal channels in a single fully dense body, free of casting porosity.
Blow-out preventer (BOP) parts Safety-critical parts that rely on the defect-free, fully consolidated microstructure.
Venturis Precise internal flow geometry with smooth, dense surfaces.
Wye pieces Junction geometry consolidated in one body instead of welded from segments.
Goosenecks Complex bends produced in one dense component without weld seams.
Blind tees Closed-end geometries produced fully dense without fabrication.
Swivels Rotating interfaces that rely on full material integrity in demanding service.

 

Industries served by HIP

Industries served by hot isostatic pressing (HIP) components from Sverdrup Steel
Industry Typical HIP components
Oil and Gas Manifolds, valve blocks, chokes, hubs, BOP parts
Chemical Pump and motor casings, fittings, valve blocks
Marine Swivels, connectors, system components
Nuclear Small modular reactor components and safety-critical parts
Defence High-integrity components for demanding platforms
Aerospace Structural parts with complex internal geometry
Sverdrup Steel employee wraps lean duplex in foil, symbolizing our value-added processing and services

Value-Added Processing & Services

A near-net-shape HIP component rarely arrives alone. It lands in a project that also needs the right material grade, verified properties, machined interfaces and dependable logistics.

At Sverdrup Steel, you can gather the full scope from one supplier: we supply duplex and superduplex, austenitic alloys, nickel alloys, martensitic alloys, heat-resistant alloys and low-alloy steels in addition to titanium, and our service centers and network of reliable partners cover machining from specification to delivery.

Explore our services relevant to HIP projects below:

Value-added services supporting hot isostatic pressing (HIP) component projects at Sverdrup Steel
Processing Service Capabilities & Features
Material Testing & Recertification A broad range of material testing and recertification performed to the highest regulatory standards.
Hot Extrusion Extruded profiles and shapes in stainless steels and high-performance alloys for custom applications.
Bored Bars & Deep Hole Drilling Deep hole drilling for components requiring precise, straight internal bores.
Laser, Plasma & Water Cutting Cut from plate details in both simple and complex shapes with sharp edges and high accuracy.
Automatic Container Loading Indoor LoadPlate handling ensures goods are loaded safely and protected from weather conditions.

To specify the right grade for your component, try our PREN calculator or the corrosion class guide, and see our NORSOK compliance work.

 

How Can We Help?

At Sverdrup Steel, we do more than supply materials, we provide expertise, innovation, and solutions that add value for our clients. Our commitment to customer service, flexibility, technical expertise, and reliability ensures that we remain a trusted partner for high-performance alloy solutions tailored to your industry’s needs.

Partner with Sverdrup Steel. Together, we forge a greener future.

Contact us for a detailed estimate and see how we can help.

Contact us

F.A.Q.

  • What is hot isostatic pressing (HIP)?

    Hot isostatic pressing, or HIP, is a powder metallurgy process that converts gas-atomized metal powder into fully dense, near-net-shape components. The powder is sealed in a mild steel capsule and consolidated under high argon pressure at elevated temperature, below the melting point. The result is a solid part with a fine microstructure, 100% density and practically no inclusions.

  • Why choose HIP components instead of castings or forgings?

    HIP offers greater design freedom than casting, forging or fabrication, and produces defect-free material with no cracks, porosity or stringers. In duplex stainless steels, the fine HIP microstructure reduces the risk of HISC. Near-net-shape blanks also cut welding, machining, inspection and repair, which shortens lead times and lowers total cost.

  • What materials can be produced by HIP?

    HIP components are available in duplex and super duplex stainless steels such as UNS S32750 and S32760, austenitic stainless steels like 316L, nickel alloys including Alloy 625 (UNS N06625), martensitic and precipitation hardening steels such as 17-4 PH, tool steels and metal matrix composites. Grade availability depends on the project, so contact us to discuss your specification.

  • What products are typically manufactured with HIP?

    Typical HIP products include manifolds, hubs and connectors, valve blocks, chokes, bends, tees and fittings, pump and motor casings, blow-out preventer parts, venturis, wye pieces, goosenecks, blind tees and swivels. They are used across the oil and gas, chemical, marine, nuclear, defence and aerospace industries.

  • How large can a HIP component be?

    Via our partner MTC Powder Solutions in Sweden, single HIP components can measure up to 1800 mm in diameter and 3550 mm in height, with a maximum weight of approximately 25 tonnes. The mild steel can is removed after pressing by machining or pickling.

  • Can Sverdrup Steel deliver HIP components for oil and gas projects?

    Yes. We supply near-net-shape HIP components to the energy and heavy industry market together with our partner MTC Powder Solutions in Sweden. For quotations and technical discussion, contact Area Manager Roald Fosse in Bergen, or send your drawing and material specification through our contact form.